nfs挂载的硬盘用qb下载不超过30m每秒的写入

AceCandy

[i=s] 本帖最后由 AceCandy 于 2025-3-1 18:36 编辑 [/i]<br /> <br />

当前A机器使用飞牛，使用nfs共享了硬盘，B机器也是飞牛进行挂载这块共享硬盘

正常家里都是2500M的全双工网线，通过路由器接入，外网速度1000M左右。

然后在B机器上使用qb下载的时候只有30m每秒的速度写入共享硬盘，怀疑是挂载方式导致。两个系统均为0.8.34版本。

iperf3交互可以达到差不多2.5G

Accepted connection from 192.168.1.249, port 40958
[  5] local 192.168.1.205 port 5201 connected to 192.168.1.249 port 40960
[ ID] Interval           Transfer     Bitrate
[  5]   0.00-1.00   sec   268 MBytes  2.25 Gbits/sec                
[  5]   1.00-2.00   sec   270 MBytes  2.27 Gbits/sec                
[  5]   2.00-3.00   sec   272 MBytes  2.28 Gbits/sec                
[  5]   3.00-4.00   sec   259 MBytes  2.18 Gbits/sec                
[  5]   4.00-5.00   sec   270 MBytes  2.27 Gbits/sec                
[  5]   5.00-6.00   sec   258 MBytes  2.17 Gbits/sec                
[  5]   6.00-7.00   sec   265 MBytes  2.23 Gbits/sec                
[  5]   7.00-8.00   sec   266 MBytes  2.23 Gbits/sec                
[  5]   8.00-9.00   sec   268 MBytes  2.25 Gbits/sec

B机器挂载参数如下：

➜  ~ mount | grep nfs
nfsd on /proc/fs/nfsd type nfsd (rw,relatime)
mount.trim_nfs on /vol02/1000-4-192.168.1.205-0-7efa17c4848a81e9410876cd8ac9ecbf- type fuse.mount.trim_nfs (rw,nosuid,nodev,relatime,user_id=0,group_id=0,allow_other)

A机器NFS参数如下：

cat /etc/exports
# /etc/exports: the access control list for filesystems which may be exported
#               to NFS clients.  See exports(5).
#
# Example for NFSv2 and NFSv3:
# /srv/homes       hostname1(rw,sync,no_subtree_check) hostname2(ro,sync,no_subtree_check)
#
# Example for NFSv4:
# /srv/nfs4        gss/krb5i(rw,sync,fsid=0,crossmnt,no_subtree_check)
# /srv/nfs4/homes  gss/krb5i(rw,sync,no_subtree_check)
#
/fs/1000/nfs  *(rw,async,no_wdelay,insecure,all_squash,no_subtree_check,insecure_locks,sec=sys,anonuid=1000,anongid=1000,fsid=1000)

请问下是需要手动调参还是什么原因呢，官方看到求帮解答一下，感谢🙏