友善R4SE支持

别样温暖 · 2026-1-12 10:48:31

能否支持下友善的R4SE，RK3399，4G内存，32G的EMMC。看到已有R4S，这个是它的升级版，更适合做NAS。

飞牛产品同学 · 2026-1-13 16:25:14

感谢反馈，我们会将它记录下来，后续根据评估结果推进

别样温暖 · 2026-1-14 12:36:17

十分感谢，这个的保有量还是很多的，也会有很多之前玩软路由的朋友乐于参与测试。

小霸王1213 · 2026-5-9 15:52:18

飞牛产品同学发表于 2026-1-13 16:25
感谢反馈，我们会将它记录下来，后续根据评估结果推进

之前看到还有R4SE的固件下载，但是之前测试的时候通过usb烧录也是无法启动的
目前我看到就只有r4s的固件了
这是usb烧录到r4se之后的启动日志

Connecting to COM4...
Connected.
DDR Version 1.30 20230417
In
channel 0
CS = 0
MR0=0x98
MR4=0x3
MR5=0xFF
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0xFF
CS = 1
MR0=0x18
MR4=0x3
MR5=0xFF
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0xFF
channel 1
CS = 0
MR0=0x98
MR4=0x1
MR5=0xFF
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0xFF
CS = 1
MR0=0x18
MR4=0x3
MR5=0xFF
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0xFF
channel 0 training pass!
channel 1 training pass!
change freq to 416MHz 0,1
Channel 0: LPDDR4,416MHz
Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB
Channel 1: LPDDR4,416MHz
Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=16 Size=2048MB
256B stride
channel 0
CS = 0
MR0=0x98
MR4=0x3
MR5=0xFF
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0xFF
CS = 1
MR0=0x18
MR4=0x3
MR5=0xFF
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0xFF
channel 1
CS = 0
MR0=0x98
MR4=0x1
MR5=0xFF
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0xFF
CS = 1
MR0=0x18
MR4=0x3
MR5=0xFF
MR8=0x8
MR12=0x72
MR14=0x72
MR18=0x0
MR19=0x0
MR24=0x8
MR25=0xFF
channel 0 training pass!
channel 1 training pass!
channel 0, cs 0, advanced training done
channel 0, cs 1, advanced training done
channel 1, cs 0, advanced training done
channel 1, cs 1, advanced training done
change freq to 856MHz 1,0
ch 0 ddrconfig = 0x101, ddrsize = 0x2020
ch 1 ddrconfig = 0x101, ddrsize = 0x2020
pmugrf_os_reg[2] = 0x3AA1FAA1, stride = 0xD
ddr_set_rate to 328MHZ
ddr_set_rate to 666MHZ
ddr_set_rate to 416MHZ, ctl_index 0
ddr_set_rate to 856MHZ, ctl_index 1
support 416 856 328 666 MHz, current 856MHz
OUT
Boot1 Release Time: May 26 2022 18:14:35, version: 1.30
CPUId = 0x0
ChipType = 0x10, 321
mmc_set_bus_width: 1
EmmcClk: 375KHZ
mmc_switch index:183, value:0x2
mmc_switch index:185, value:0x2
EmmcClk: 375KHZ
mmc_set_bus_width: 8
EmmcClk: 200000KHZ
SdmmcInit=2 0
BootCapSize=100000
UserCapSize=59640MB
FwPartOffset=2000 , 100000
NeedKHz=200KHz, Clock=12000KHz
NeedKHz=200KHz, Clock=12000KHz
NeedKHz=200KHz, Clock=12000KHz
mmc0:cmd8,20
mmc0:cmd5,20
mmc0:cmd55,20
mmc0:cmd1,20
NeedKHz=200KHz, Clock=12000KHz
NeedKHz=200KHz, Clock=12000KHz
mmc0:cmd8,20
mmc0:cmd5,20
mmc0:cmd55,20
mmc0:cmd1,20
NeedKHz=200KHz, Clock=12000KHz
NeedKHz=200KHz, Clock=12000KHz
mmc0:cmd8,20
mmc0:cmd5,20
mmc0:cmd55,20
mmc0:cmd1,20
NeedKHz=200KHz, Clock=12000KHz
SdmmcInit=0 1
StorageInit ok = 78739
SecureMode = 0
SecureInit read PBA: 0x4
SecureInit read PBA: 0x404
SecureInit read PBA: 0x804
SecureInit read PBA: 0xc04
SecureInit read PBA: 0x1004
SecureInit read PBA: 0x1404
SecureInit read PBA: 0x1804
SecureInit read PBA: 0x1c04
SecureInit ret = 0, SecureMode = 0
atags_set_bootdev: ret:(0)
GPT part: 0, name: BOOT, start:0x10000, size:0xa2800
GPT part: 1, name: rootfs, start:0xba800, size:0x676800
no find partition:uboot.
LoadTrust Addr:0x4000
No find bl30.bin
No find bl32.bin
Load uboot, ReadLba = 2000
Load OK, addr=0x200000, size=0xde858
RunBL31 0x40000 @ 109802 us
NOTICE: BL31: v1.3(release):8f40012ab
NOTICE: BL31: Built : 14:20:53, Feb 16 2023
NOTICE: BL31: Rockchip release version: v1.1
INFO: GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3
INFO: Using opteed sec cpu_context!
INFO: boot cpu mask: 0
INFO: plat_rockchip_pmu_init(1203): pd status 3e
INFO: BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR: Error initializing runtime service opteed_fast
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x200000
INFO: SPSR = 0x3c9
U-Boot 2025.10-fnOS-c106-02252-g1e3858d7b895 (Feb 02 2026 - 04:16:20 +0000)
SoC: Rockchip rk3399
Reset cause: POR
Model: FriendlyElec NanoPi R4S
DRAM: 4 GiB (total 3.9 GiB)
PMIC: RK808
Core: 297 devices, 30 uclasses, devicetree: separate
MMC: mmc@fe320000: 1
Loading Environment from MMC... MMC Device 0 not found
*** Warning - No MMC card found, using default environment
In: serial,usbkbd
Out: serial,vidconsole
Err: serial,vidconsole
Model: FriendlyElec NanoPi R4S
Net: eth0: ethernet@fe300000
Hit any key to stop autoboot: 0
Scanning for bootflows in all bootdevs
Seq Method State Uclass Part Name Filename
--- ----------- ------ -------- ---- ------------------------ ----------------
Scanning global bootmeth 'efi_mgr':
Card did not respond to voltage select! : -110
Cannot persist EFI variables without system partition
USB EHCI 1.00
USB EHCI 1.00
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.10
Bus usb@fe380000: 1 USB Device(s) found
Bus usb@fe3c0000: 1 USB Device(s) found
Bus usb@fe800000: 1 USB Device(s) found
Bus usb@fe900000: 1 USB Device(s) found
Scanning bootdev 'mmc@fe320000.bootdev':
Card did not respond to voltage select! : -110
No bootdevs for 'mmc0'
Unknown uclass 'nvme' in label
Unknown uclass 'scsi' in label
Scanning bootdev 'ethernet@fe300000.bootdev':
ethernet@fe300000 Waiting for PHY auto negotiation to complete....... done
Speed: 1000, full duplex
BOOTP broadcast 1
BOOTP broadcast 2
DHCP client bound to address 192.168.123.187 (253 ms)
missing environment variable: pxeuuid
Retrieving file: pxelinux.cfg/01-3e-94-14-61-d5-31
Speed: 1000, full duplex
Using ethernet@fe300000 device
TFTP from server 192.168.123.1; our IP address is 192.168.123.187
Filename 'pxelinux.cfg/01-3e-94-14-61-d5-31'.
Load address: 0xe00000
Loading: T T T T
[END] 2026/5/9 15:48:08

复制代码

		自动登录	找回密码
密码			立即注册

友善R4SE支持

点评

本帖子中包含更多资源

社区上线纪念勋章

社区共建团荣誉勋章

飞牛百度网盘玩家

fnOS1.0上线纪念勋章