OESP安装的Arm版飞牛，时不时出现硬盘损坏，重启完又恢复正常。没有开硬盘休眠。以前装casaos时候没有出现过问题，是飞牛的读写频率更高吗？
sudo smartctl -a /dev/sda
smartctl 7.3 2022-02-28 r5338 [aarch64-linux-6.12.41-trim] (local build)
Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: J.ZAO 3 SERIES 2.5 INCH 960GB SATA SSD
Serial Number: NBN380T001687
LU WWN Device Id: 5 3a5a27 0030c08f3
Firmware Version: SN12155
User Capacity: 960,197,124,096 bytes [960 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
TRIM Command: Available, deterministic, zeroed
Device is: Not in smartctl database 7.3/6178
ATA Version is: ACS-4 (minor revision not indicated)
SATA Version is: SATA 3.2, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Fri Jul 3 10:19:31 2026 CST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 33) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 85) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x0031) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 20
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
5 Reallocated_Sector_Ct 0x1300 100 100 010 Old_age Offline - 0
9 Power_On_Hours 0x1200 100 100 000 Old_age Offline - 4846
12 Power_Cycle_Count 0x1200 100 100 000 Old_age Offline - 167
164 Unknown_Attribute 0x0000 100 100 000 Old_age Offline - 17182228497
165 Unknown_Attribute 0x0000 100 100 000 Old_age Offline - 36
166 Unknown_Attribute 0x0000 100 100 000 Old_age Offline - 4
167 Unknown_Attribute 0x2200 100 100 000 Old_age Offline - 17
194 Temperature_Celsius 0x2200 031 031 000 Old_age Offline - 31 (Min/Max 23/39)
199 UDMA_CRC_Error_Count 0x1200 100 100 000 Old_age Offline - 0
241 Total_LBAs_Written 0x3200 100 100 000 Old_age Offline - 1314
242 Total_LBAs_Read 0x3200 100 100 000 Old_age Offline - 1419
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 4602 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
